The FLEC® has been validated and used in research for many years.
Below is a publication list of journal articles, abstracts, poster or oral presentations where the FLEC or CHEMATEC’s other products have been in focus.
If you have anything that can be added to the list, we encourage you to contact CHEMATEC.
2015 |
Liang, Yirui; Xu, Ying The influence of surface sorption and air flow rate on phthalate emissions from vinyl flooring: Measurement and modeling Journal Article In: Atmospheric Environment, vol. 103, pp. 147 - 155, 2015, ISSN: 1352-2310. Abstract | Links | BibTeX | Tags: Air flow rate, Chamber test, Model, Phthalates, Surface absorption, SVOCs @article{LIANG2015147,This study investigated the influences of surface sorption and air flow rate on the emission of phthalates from building materials. Controlled tests were conducted in specially designed stainless steel and wood chambers, and the steady-state concentration in the stainless steel chamber was about 2–3 times higher than that in the wood chamber for di(2-ethylhexyl) phthalate (DEHP) and diisononyl phthalate (DINP). The emission rate of phthalates increased in the wood chamber due to the diffusion mass flow through the chamber wall (i.e., surface absorption). The adsorption isotherm of phthalates on the stainless steel surface and the absorption parameters (i.e., diffusion and partition coefficients) of phthalates on the wood surface were determined experimentally, and the values were comparable to those in the literature. The equilibration time scale for phthalates absorbed to the sink reservoir in actual indoor environments was estimated and can be substantial (approximately 80 years), indicating that surface absorption may continuously drive phthalates from their indoor sources to various sinks and thus significantly increase the emission rate of phthalates. The gas-phase concentration of DEHP was measured in two stainless steel chambers operated at flow rates of 300 mL/min and 3000 mL/min, respectively, which were both adjusted to 1000 mL/min after steady state was reached. The gas-phase concentration of DEHP in the chamber was very sensitive to the chamber air flow rate, and higher air flow rates resulted in lower concentration levels. However, the increased emission rate compensated for the dilution in the gas phase and made the DEHP concentration not drop substantially with an increase in the air flow rate. Independently measured or calculated parameters were used to validate a semi-volatile organic compounds (SVOCs) emission model that included absorptive surfaces and for a range of air flow rates, with excellent agreement between the model predictions and the observed chamber concentrations of phthalates. |
2009 |
Kagi, N; Fujii, S; Tamura, H; Namiki, N Secondary VOC emissions from flooring material surfaces exposed to ozone or UV irradiation Journal Article In: Building and Environment, vol. 44, no. 6, pp. 1199 - 1205, 2009, ISSN: 0360-1323. Abstract | Links | BibTeX | Tags: Chamber test, Emission, Secondary emission, Volatile organic compounds @article{KAGI20091199,Chemical reactions on the surface of building materials can lead to secondary emissions from these materials that influence indoor air quality. Many studies have been made on the physical processes that influence material emissions. However, there are only a few studies on secondary emissions resulting from exposure of building material surfaces to ozone or ultraviolet (UV) irradiation. Therefore, this study was aimed at elaborating on the emission of chemicals resulting from chemical reactions initiated by the exposure of the surface of flooring materials to ozone or UV irradiation. The laboratory tests were conducted to estimate gas-phase emissions from the flooring materials when they were exposed to ozone or various kinds of light irradiation (infrared, sunlight, UV-A and UV-B lamps). The infrared and sunlight lamps significantly increased the temperature of the test specimens and, in turn, increased the emission rate for various organic compounds. The flooring materials used in this study had been treated with UV-cured surface coatings during their manufacturing. As a result, when exposed to UV irradiation, chemical transformations occurred resulting in the emission of a number of secondary products, including formaldehyde, acetaldehyde, cyclohexanone and benzaldehyde. Ozone reacted with chemicals present in the flooring materials to increase the emission rates of formaldehyde and acetaldehyde. Hence, the exposure of ozone and UV irradiation increased the secondary emissions of formaldehyde, even though the low formaldehyde emission type of flooring material was employed. |