The FLEC® has been validated and used in research for many years.
Below is a publication list of journal articles, abstracts, poster or oral presentations where the FLEC or CHEMATEC’s other products have been in focus.
If you have anything that can be added to the list, we encourage you to contact CHEMATEC.
2016 |
Liu, Xiaoyu; Guo, Zhishi; Krebs, Kenneth A; Greenwell, Dale J; Roache, Nancy F; Stinson, Rayford A; Nardin, Joshua A; Pope, Robert H Laboratory study of PCB transport from primary sources to settled dust Journal Article In: Chemosphere, vol. 149, pp. 62 - 69, 2016, ISSN: 0045-6535. Abstract | Links | BibTeX | Tags: Chamber testing, Dust/air partition, Dust/source partition, Polychlorinated biphenyls (PCBs), Settled dust @article{LIU201662,Dust is an important sink for indoor air pollutants, such as polychlorinated biphenyls (PCBs) that were used in building materials and products. In this study, two types of dust, house dust and Arizona Test Dust, were tested in a 30-m3 stainless steel chamber with two types of panels. The PCB-containing panels were aluminum sheets coated with a PCB-spiked primer or caulk. The PCB-free panels were coated with the same materials but without PCBs. The dust evenly spread on each panel was collected at different times to determine its PCB content. The data from the PCB panels were used to evaluate the PCB migration from the source to the dust through direct contact, and the data from the PCB-free panels were used to evaluate the sorption of PCBs through the dust/air partition. Settled dust can adsorb PCBs from air. The sorption concentration was dependent on the congener concentration in the air and favored less volatile congeners. When the house dust was in direct contact with the PCB-containing panel, PCBs migrated into the dust at a much faster rate than the PCB transfer rate due to the dust/air partition. The dust/source partition was not significantly affected by the congener's volatility. For a given congener, the ratio between its concentration in the dust and in the source was used to estimate the dust/source partition coefficient. The estimated values ranged from 0.04 to 0.16. These values are indicative of the sink strength of the tested house dust being in the middle or lower-middle range. |
Lyng, Nadja Lynge; Gunnarsen, Lars; Andersen, Helle Vibeke; Kofoed-Sørensen, Vivi; Clausen, Per Axel Measurement of PCB emissions from building surfaces using a novel portable emission test cell Journal Article In: Building and Environment, vol. 101, pp. 77 - 84, 2016, ISSN: 0360-1323. Abstract | Links | BibTeX | Tags: Building materials, emission rate, Emission test cell, Indoor air, Polychlorinated biphenyls (PCBs), Semivolatile organic compound (SVOCs) @article{LYNG201677,Polychlorinated biphenyls (PCBs) were used in building materials like caulks and paints from 1930–1970s and in some cases that caused elevated PCB concentrations in the indoor air at levels considered harmful to occupant health. PCBs are semivolatile organic compounds and capable of spreading from the original source to adjacent materials, indoor air and via adsorption from the air to indoor surfaces, causing secondary contaminations. Remediation of buildings with unsatisfactory indoor air concentrations is a complex and difficult task due to the secondary contamination of building materials and there is a need to prioritise remediation measures on different materials. An inexpensive and portable emission test cell was developed to resemble indoor conditions in relation to the area specific ventilation rate. Emissions were measured using the test cell in the laboratory on freshly made PCB paint. Further, the chamber was used for determining emissions from PCB-containing building materials in the field as well as remediated walls. The measurements showed that sorption of PCBs to chamber walls was insignificant after 2–4 days of exposure to the source. Over a period of two weeks emission rates did not change from any of the tested surfaces, however in the laboratory experiment emission rates decreased over a longer period (48 days) and was most pronounced for the lower chlorinated PCBs. |